Uvp B-100 Series Manuel d'utilisateur télécharger pdf

B-100 Series Ultraviolet Lamps

Operating Instructions

These Instructions cover UVP’s high-intensity 100-watt

B-100 series lamps (115V and 220V). The B-100AP,

B-100AP/R and B-100YP models are manufactured with

UVP’s Cool-Touch™ plastic housing. B-100A, B-100A/R

and B-100Y models are manufactured of a durable

scratch-resistant, powder-painted aluminum. The

B-100Y and B-100YP models feature a yellow filter.

Lamp and accessory drawings and replacement parts

lists for each model are included in these instructions.

This manual covers the following lamp part numbers:

Part Numbers

Model 115V 230V

B-100AP 95-0127-01 95-0127-02

B-100AP/R 95-0127-06 95-0127-07

B-100YP 95-0127-03 95-0127-04

B-100Y 95-0044-24 95-0044-18

B-100A 95-0044-22 95-0044-02

B-100A/R 95-0044-03 95-0044-03

General Information for Ultraviolet Inspection

Make tests in a darkened area for best contrast. Fluorescence may be bright or dim, depending on amount

of fluorescing agent present. Be careful to distinguish fluorescence from blue light reflection on polished

metal surfaces. UVP Model UVC-503 Safety Goggles are recommended to eliminate blue haze resulting

from eye fluorescence caused by reflected longwave ultraviolet radiation.

Installation

An 8-foot primary and secondary line cord is supplied on all units except the B-100AP/R and B-100A/R which

come with 8-foot primary and 20-foot secondary line cords. If the receptacle is not fitted with 3-prong plug,

use a 2-prong adapter and attach grounding lead to screw center of receptacle plate. Some units may ship

with bare wire leads. Connect the appropriate plug for your area.

Operation

Turn on/off switch on transformer base to ON position for starting. Although a cool lamp starts immediately,

allow approximately five minutes to reach full brilliance. When use is intermittent, it is preferable to leave the

lamp burning. This assures longer bulb life and avoids delay in restarting. Restarting does not take place

immediately as the mercury vapor within the bulb must cool. Delay is typically 4 to 8 minutes. Any interruption

in the power supply, such as an excessive drop in voltage, will extinguish the arc. Restarting typically will be

delayed while the mercury vapor cools. Full voltage must be restored to permit the arc to strike.

While mounted on the transformer base, the lamp housing can rotate 360°. For handheld use, detach the lamp

housing from the transformer base.

81-0093-01 Rev N

B-100AP

1 2 3 4

Résumé du contenu

Page 1 - Operating Instructions

B-100 Series Ultraviolet Lamps Operating Instructions These Instructions cover UVP’s high-intensity 100-watt B-100 series lamps (115V and 220V). The

Page 2 - B-100AP, B-100AP/R, B-100YP

Replacement Parts List Parts lists are provided for the B-100 lamp models. Two parts lists are shown: one for the Cool-Touch housing lamps and one

Page 3 - Accessories

CAUTION 1. Wear hand and eye protection if filter glass is cracked. Replace filter as soon as possible. 2. To avoid electrical shock hazard, unpl

Page 4 - Product Warranty

The Finger Guard, to keep fingers away from the filter glass, easily snaps into place on the face of the Cool-Touch lamps. To install, remove the la

Commentaires sur ces manuels

Pas de commentaire

Uvp B-100 Series Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Éclairage Uvp B-100 Series. UVP B-100 Series User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Éclairage Uvp B-100 Series