search

Uvp TB-107 Transilluminator Ballast Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Santé et hygiène Uvp TB-107 Transilluminator Ballast. UVP TB-107 Transilluminator Ballast User Manual Manuel d'utilisatio

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 6
  • Table des matières
  • MARQUE LIVRES
    • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 0
TB-107 Rev STD
T
T
e
e
c
c
h
h
n
n
i
i
c
c
a
a
l
l
B
B
u
u
l
l
l
l
e
e
t
t
i
i
n
n
T
T
B
B
-
-
1
1
0
0
7
7
Transilluminator Ballast Replacement
Overview
The purpose of this Technical Bulletin is to explain the process of uninstalling and reinstalling a
transilluminator ballast on a UVP transilluminator.
To complete this procedure, the following tools and parts will be required:
• Phillips-head screwdriver
• 1/4” nut driver
• New transilluminator ballast
Caution: This procedure requires a moderate level of technical competence. If you are not
comfortable working with electronics, tools and/or related components, contact UVP for
assistance.
Removal Procedure
When performing the following procedure, place all components (screws, nuts, etc.) in a secure
location as they will be reused for installation.
1. Turn off the transilluminator by placing the power switch on the front of the unit in the OFF
position. Then, unplug the unit from the wall power.
2. Remove the four Phillips-head screws and washers securing the transilluminator filter frame
to the body of the transilluminator. Lifting up, remove the transilluminator filter frame from the
transilluminator body. Place the filter frame aside.
Two of Four
Phillips-Head
Screws and
Washers
Transilluminator
Filter Frame
Transilluminator
Body
Vue de la page 0
1 2 3 4 5 6

Résumé du contenu

Page 1 - Removal Procedure

TB-107 Rev STD TTeecchhnniiccaall BBuulllleettiinn TTBB--110077 Transilluminator Ballast Replacement Overview The purpose of this Technical Bul

Page 2

3. Inside the unit, locate the side reflector panels which are two removable reflective metal panels located at each end of the transilluminator ligh

Page 3

7. Place the new ballast next to the old ballast, also atop the fixed reflector panels, in the same orientation as the old ballast. 8. Grasp one

Page 4 - Installation Procedure

10. Working wire by wire, repeat these steps until all wires have been transferred from the old to the new ballast, taking care to match the location

Page 5

As the edges of the side reflector panels are sharp, ensure that all wiring is moved out of the way during installation of the side reflector panels t

Page 6 - Technical Support

Technical Support Contact UVP Technical Support for additional assistance: If you are in North America, South America, East Asia or Australia: If yo

Commentaires sur ces manuels

Pas de commentaire
Produits connexes et manuels pour Santé et hygiène Uvp TB-107 Transilluminator Ballast
Santé et hygiène Uvp 81-0117-01 EL Series Lamps Manuel d'utilisateur   (9 pages)
Santé et hygiène Uvp 81-0203-01 3UV Lamps Manuel d'utilisateur   (3 pages)
  • Securitron White Mountain Goodway Memory Experts CME
  • Anton/Bauer Piles rechargeables MD Non Acer Tablettes Honeywell Objectifs d'appareil photo Metabo Aspirateurs
  • Casio EXILIM EX-M20U Philips SLA5500 Eiki LC-XB40 Dell Internal PCIe PAL/SECAM/DVB-T Desktop TV Tuner Diode-led INFINILINE
  • Moon 230D Manuel du propriétaire Philips MCM700/12 Manuel de l'utilisateur Acer P7505 Manuel de l'utilisateur Samsung UE65LS003AU Manuel de l'utilisateur Gossen STARLITE 2 Manuel de l'utilisateur